4CH Verstärker
D4-1300 DSP Kompakter multifunktionaler Line-Array-Leistungsverstärker der Klasse D
punkt nr.: D4-1500 DSP
Model: D4-1500 DSP
Channel: 4-channel power amplifier
Feature: 1U/Digital Amp/2 Ohms Stable
Output Power:
8Ω Stereo Power (RMS): 1,500W X 4CH
4Ω Stereo Power (RMS): 2,500W X 4CH
2Ω Stereo Power (RMS): 3,000W X 4CH
Warranty: 3 Years
Channel: 4-channel power amplifier
Feature: 1U/Digital Amp/2 Ohms Stable
Output Power:
8Ω Stereo Power (RMS): 1,500W X 4CH
4Ω Stereo Power (RMS): 2,500W X 4CH
2Ω Stereo Power (RMS): 3,000W X 4CH
Warranty: 3 Years
beschreibung
D4-1500 DSP Class D Audio AMPLIFIER Feature:
FRONT PANEL FEATURE
REAR PANEL FEATURE
Dimensions and Cooling system
ALLDSP ALLControl
The new D series digital amplifier also has the option to add a DSP function, Our D series DSP amplifier uses an ALLDSP system from Germany. It is suited for Windows, Mac and ios systems.
The application for iPad or iPhone can be downloaded and installed from the Apple Store.
App Name:ALLControl,Remind you it is Paid-for Software.（The software Password is Develo_p）
For the Remote Operation Software (Windows and Mac) and Manual, Please check the Download link or contact us!
Note that for a Windows computer, there are separate applications for Windows 32-bit and 64-bit.
Attention: You cannot connect the unit to the network through the USB or Ethernet at the same time. You can only control the unit from one platform at the same time if you switch from one platform to another, you MUST shut down the control software at the previous platform first.
Local connectivity of the device to the control computer from a front-panel USB connector is also possible to download initial settings or as a fallback in case of network failure.
►Unit Window: Main Panel
Unit window shows the unit window from which all setup screens and options can be reached.Clicking the exit cross will close the software but leave the network Control program running.
►Input Channel Settings Screen
Clicking on an Input channel number in the Unit window will bring up the input channel settings screen see Figure above. In this screen, individual input channels can be equalized and/or filtered.
Settings screen:
►Crossover Settings Window
When you click X-over in the left unit window function list, most of the screen is dedicated to the controls and indicators for setting up the cross over filters as shown in Figure.
Settings screen:
►Output Channel Settings Screen
As shown in the picture above, faders are shown for each of the input channels. This will allow mixing each of the input signals to each individual Output channel. Even if Input channels are set to Linked in the Unit window, it is still possible here to mix individual Input channels to an Output channel in any desired ratio. Level setting are shown numerically below each fader. The available range is from -48 dB to 0 dB. As in other screen, double clicking a fader resets it to default.
A complete control screen is available for each Output channel. The graphical area reflects the Crossover settings for the channel in addition to any equalization settings set up in this screen, and is very similar to the available settings in the individual Input channel screens.The status of an element is always reflected in the blue on/off button next to each element.
Settings screen:
►More Dsp Details please download:
D Series AllDSP ALLControl Software Download (64 bit)
D Series AllDSP ALLControl Software Download (32 bit)
| ●1U ultra-thin body, lightweight and compact design |
| ●Imported Japanese NCC capacitors for high-quality sound output |
| ●GaN gallium nitride material, low heat generation, less noise, and low distortion! |
| ●Strong bass, full and sweet mid range, clear and delicate high-frequency |
| ●High efficiency, energy conservation, and environmental protection. Saving operating expenses. |
| ●With active PFC and soft-switching technology, the power correction factor can reach up to 0.99, providing strong adaptability. |
| ●Work under wide voltage range of 90V-270V, allowing it to adapt to harsh power grid environments and provide continuous power supply. |
| ●With stable and reliable 2Ω driving capability, it is perfectly suited for line array speaker systems. |
| ●Standby sleep mode, power-saving and durable |
| ●ROHS and CE certified, with national quality inspection reports and energy-saving and environmental certifications, compliant with various 3C tests. |
| ●High-end components from top international manufacturers, with advanced and reliable circuits. |
| ●Strict and reliable production processes and user experience testing |
FRONT PANEL FEATURE
REAR PANEL FEATURE
Dimensions and Cooling system
|
NOTE:
The size is 437mm inside of the device(without the cover plate and front panel).The size is around 472mm of the complete device,but a little bit different size in the different front panels.Some series with different size have not shown,please learn it in the parameter. Tunnel through cooling system Cold air comes in from the front panel of the equipment and forms a duct through the radiator to take the heat away and out from the rear panel of the equipment. |
 |
ALLDSP ALLControl
The new D series digital amplifier also has the option to add a DSP function, Our D series DSP amplifier uses an ALLDSP system from Germany. It is suited for Windows, Mac and ios systems.
The application for iPad or iPhone can be downloaded and installed from the Apple Store.
App Name:ALLControl,Remind you it is Paid-for Software.（The software Password is Develo_p）
For the Remote Operation Software (Windows and Mac) and Manual, Please check the Download link or contact us!
Note that for a Windows computer, there are separate applications for Windows 32-bit and 64-bit.
|
Parameters of DSP Module
|
|
|
Digital signal processor
|
64 bit multimode, 4 in and 4 o]ut
|
|
AD converter
|
120db Dynamic Range
|
|
DA converter
|
110db Dynamic Range
|
|
Storage preset
|
100
|
|
Signal input
|
Analog/optional Dante
|
|
Delay range
|
0-10ms
|
|
Equalizer
|
5-segment grouping equalization, 10 segment input/output equalization
|
|
Frequency division filter
|
Linkwitz Reiley, Belsel, Butterworth
|
|
FIR filter
|
4x144taps
|
Attention: You cannot connect the unit to the network through the USB or Ethernet at the same time. You can only control the unit from one platform at the same time if you switch from one platform to another, you MUST shut down the control software at the previous platform first.
Local connectivity of the device to the control computer from a front-panel USB connector is also possible to download initial settings or as a fallback in case of network failure.
►Unit Window: Main Panel
Unit window shows the unit window from which all setup screens and options can be reached.Clicking the exit cross will close the software but leave the network Control program running.
►Input Channel Settings Screen
Clicking on an Input channel number in the Unit window will bring up the input channel settings screen see Figure above. In this screen, individual input channels can be equalized and/or filtered.
Settings screen:
|
●Filtering and EQ
●Input channel transfer function curve ●Screen expansion and legends ●Input Gain, Mute ●Delay, limiter, compressor ●RMS compressor |
 |
●Screen expansion and legends On the left-hand side of the graphical screen are four icons to help precise settings. The top Arrow icon expands the graphical screen to the size of the window.Clicking this icon again from the expanded screen expands it to the full display size. In either of the expanded settings, clicking the X-icon at the top left will collapse the graphical area to the default setting. The T(ext) icon will place the frequency, Q, and gain values of each EQ and filter setting in the graphical screen. For very accurate settings of EQ or filtering you can click the Looking Glass icon. |
 |
●Delay, limiter, compressor Settings for channel delay, limiter (-48 to +24 dBu), and limit release rate (10 to 100 dB/s) settings.Plus a button to enter the rms compressor menus. Channel delay can be set in a variety of distance or time units from the drop-down list. |
 |
●Compressor settings window Clicking on the compressor button brings up the compressor menu. In the compressor menu you can set the parameters of the rms compressor.You can set the threshold, attack, hold, and release time, the compression ratio and the make-up gain.Next to the controls is a VU meter that also displays the gain reduction (GR). Be sure to use the ‘Back’ button to return to the output menu. |
►Crossover Settings Window
When you click X-over in the left unit window function list, most of the screen is dedicated to the controls and indicators for setting up the cross over filters as shown in Figure.
Settings screen:
|
●Graphical control
●Filter type ●Gain ●Delay ●Link ●Mute, Phase Invert |
►Output Channel Settings Screen
As shown in the picture above, faders are shown for each of the input channels. This will allow mixing each of the input signals to each individual Output channel. Even if Input channels are set to Linked in the Unit window, it is still possible here to mix individual Input channels to an Output channel in any desired ratio. Level setting are shown numerically below each fader. The available range is from -48 dB to 0 dB. As in other screen, double clicking a fader resets it to default.
A complete control screen is available for each Output channel. The graphical area reflects the Crossover settings for the channel in addition to any equalization settings set up in this screen, and is very similar to the available settings in the individual Input channel screens.The status of an element is always reflected in the blue on/off button next to each element.
Settings screen:
|
●Relationship between Input- and Output settings
●Output filtering and EQ ●Output channel transfer curve ●Delay, limiter, compressor ●RMS compressor ●Change / adjusting Values |
►More Dsp Details please download:
D Series AllDSP ALLControl Software Download (64 bit)
D Series AllDSP ALLControl Software Download (32 bit)
